English

Light Steel Structure Broiler House

Light Steel Structure Broiler House

Time: 2018-12-21

Views : 1667

Product Informaition

Ⅰ.General description : 

1.Main Structure
(Steel tube truss system ) we adaopt hot-dip galvanized C section or steel tube truss beam to reduce sef-weight of design load and dosage of thesteel. At the same time, hot-diped galvanized can widely improve anti-corrosion of the steel. (The construction cycle of the steel structure work is short, which reduces the cost of the project effectively. The steel structure has strong shock resistance and can improve the comprehensive anti-seismic property of the whole house).
 
2.Substructure( Cold-formed thin-walled steel)
Roof purlin uses the hot-dip galvanized Z or C section. The way to continuous lap makes the steel frame as a whole. Wall purlin uses the hot-dip galvanized C section steel. All components adopt bolted connection, no welding, which makes the structure overall appearance smooth.


 Ⅱ.Material of main parts

1. Column: Q235, Q345 welding H section steel

2. Beam: Q235, Q345 welding H section steel

3. Purlin: Q235 C section or Z section

4. Knee brace: Q235 angle steel

5. Vertical and transversal support: Q235 angle steel, round bar or steel pipe.

6. Tie bar: Q235 steel pipe

7. Brace: Q235 round bar

8. Sleeve: Q235 steel pipe

9. Cladding system: Sandwich panels (EPS, PU, Fiber glass wool etc. ) or can use corrugated steel sheet with fiber glass wool insulation and steel wire gauze.

10. Door: Sandwich panel sliding door or roller door

11. Windows: PVC or Aluminum

12. Gutter: Stainless steel or color steel sheet

13. Rainspout: PVC


Ⅲ.Environment control of poultry shed

1.    Cooling pad system

Evaporative cooling pad system works in the condition of negative pressure, the cooling pad is installed on one side of the wall, fan installed other side. When air flow through cooling pads, the water evaporation absorbs a lot amount of heat.The height of cooling pad is 1.5-2.2m, the area of cooling pad in chicken house is about 6-8 times than the fans.

2.    ventilating system

The main parts of ventilation system is the big fan and small fan. They are controlled by the control system. The NO. of the fans to run was decided by the temperature of the poultry house.About 200m2 need 1 big fan and 15-20m need a small fan, this is the standard to design the quantity of fans in chicken house.


Ⅵ.Our full set poultry equipment including 9 units as below ( on the floor ) 


Item NO.

Description

1.

Main delivery system : inluding steel silo for feed sensor and delivery auger 

2.

Automatic pan feeding system : including feed pan , pipe ,motor , lifting device

3.

Automaitic Nipple drinking system : including nipple drinker , plsatic pipe , regulator and dose

4.

Ventilation system : inluding 50”fan, 36” fan  and air inlet

5.

Wet Cooling pad

6.

Spraying and disinfecting system

7.

Environment control system :  controller

8.

Heating system  used gas and coal 

9.

Curtain system ( used in open –type poultry house )

Ⅴ.Excerllent service we can offer : 

Our excellent design team will freely design the light steel structurepoultryhouse/ warehouse/workshop for you. If you give us the following information, we will give you an satisfactory drawing.

1. Dimension: Length, width, ridge height, eave height,  etc.
2. Doors and Windows: Dimension, quantity, installation position.
3. Local Climate: Wind load, snow load, roof load, Seismic load
4. Insulation materials: Insulated Sandwich panel or Single Steel Sheet
5. Crane beam: If you need it, it will be very helpful that you tell us its technological parameters.
6. Usage: If you tell us the application of light steel structure warehouse, we can exactly design the drawings  or match suitable materials for you.
7. Other requirements: Such as fire proofing, transparent roof, etc. Please kindly inform us, too.


Inquiry Now

If you have any questions, feedback or comments, please fill out the form below and we will reply you back as soon as possible.

+